==)--- P TO PAUSE S TO STOP ---(==

       !!WHACKOLAND!WHACKOLAND!!
       W                       W
       H -> HACKING RAMPART <- H
       A     SYSTEMS PT. I     A
       C                       C
       K     INTRODUCTION      K
       O          &            O
       '   IN DEPTH COMMAND    '
       S        SUMMARY        S
       !!WHACKOLAND!WHACKOLAND!!

  INFO ON RAMPART SYSTEMS
  -----------------------

  RAMPART SYSTEMS ARE USED BY CO'S
SUCH AS METRO,MCI,SPRINT,ECT. WE HAVE
FOUND THAT THEY ARE USUALLY SET UP LIKE
WESTERN UNION'S EASYLINK SYSTEM. HERE
IS A EXMAMPLE FOR METRO...

YOU DIAL THE LDS SERVICE WHICH IN THIS
CASE IS 314/342-1130 THEN YOU WOULD
ENTER A CODE SUCH AS XXXXXX, THEN IT 
WOULD GIVE A CARRIER. YOU HAVE TO HAVE
1200BPS TO CONNECT WITH THIS SYSTEM.

  HACKING RAMPART
  ---------------

  FIRST OFF YOU'LL HAVE TO GET A ACCT.
OR CODE TO ACCESS THE RAMPART SYSTEM TO
DO THIS YOU'LL NEED TO WRITE A SIMPLE
PROGRAM THAT WILL WARDIAL THAT LDS AND
ENTER CODES EITHER SEQ. OR RAND., AND
DO NOT HAVE IT DIAL A CARRIER LIKE ON
A REGULAR CODE HACKER. IF IT IS THE
CODE YOU ARE LOOKING FOR IT WILL GIVE A
CARRIER IMMEDIATLEY AFTER DIALING IT.
  IT WILL CONNECT 300 & 1200, BUT WILL
ONLY LET YOU ON THE MAIN SYSTEM 1200BPS
WHEN IT FINDS A CODE FOR RAMPART HAVE
IT CHECK FOR THE CARRIER DETECT, AND
RECORD THE CODE'S THAT GET THE CARRIER
DETECT.

  ] HACKING RAMPART ACCT [

  OK AFTER YOU HAVE GOTTEN THIS FAR AND
ARE CONNECTED TO THE SYSTEM, IT WILL
GIVE YOU A '>' PROMPT.  YOU CAN EITHER
ENTER 'LOG' OR 'ACCT,PW'.  WHEN YOU
ENTER LOG IT WILL SAY:
ACCT OR ID:
PASSWORD:

BASIC ACCTS ON RAMPART SYSTEMS THAT I
HAVE FOUND WERE...

ACCOUNT         -    PASSWORD
--------------       ------------------
DEMO            :    DEMO
SYSTEST         :    SYSMNGR
RAMPART         :    SYSTEST
HELP            :    SYSTEST OR HELP

  NOTE: THESE AREN'T PRIVLEDGED ACCTS.
       TO GET A PRIV. ACCT, YOU MUST
       HAVE THE RUT PASSWORD & ID.

  RAMPART SYSTEMS COMMAND SUMMARY PT I
  ------------------------------------

NOTE: YOU SHOULD READ THE INTRODUCTION
TO HACKING RAMPART SYSTEMS, BEFORE YOU
START ON THIS FILE.

OK THIS IS GOING TO MAINLY TELL ABOUT
WHAT THE COMMANDS AND SUB-COMMANDS ARE
USED FOR ON THE RAMPART SYSTEM.

HELP

THE HELP FUNCTION ENABLES THE USER TO
ENQUIRE ABOUT RAMPART SYSTEM CONCEPTS,
COMMANDS, AND SYNTAX. TYPE "HELP HELP"
FOR MORE SPECIFIC INFORMATION ON USE OF
THE HELP FUNCTION.

MORE HELP IS AVAILABLE UNDER THE SUB-
TOPICS:

HELP
ABORT
RUN
REFERRAL
TRUNK-NUMBERS
DATABASE
CHECK
EDIT

SEE HACKING RAMPART PT III FOR A SUM-
MARY FOLLOWING COMMANDS                 -------------------------------------
PUT
DISPLAY
TERMINAL
TEST
REPORT
PRIME
ROUTINE
LOGOUT
ERROR-CODES
---------------


    ->ABORT

ABORT 

ENABLES THE USER TO ABORT ROUTINE TEST-
ING OR SELECTED DEMAND TESTS.  TO STOP
TESTS ACTIVE ON A SINGLE PORT, PUT THAT
PORT OUT OF SERVICE.

DEMAND ABORTS WILL NOT COMPLETE UNTIL
THE CURRENT TRUNK UNDER TEST HAS BEEN
FULLY TESTED.

ROUTINE ABORTS ARE THE SAME AS DEMAND
ABORTS.

    > ABORT SUB CMDS <

DEMAND
ROUTINE

    ->ABORT DEMAND 
                     (OR ALL)

ABORTS ALL DEMAND TESTS FOR THE
SPECIFIED TERMINAL NUMBER. IF NO
TERMINAL NUMBER IS GIVEN, ALL DEMAND
TESTS FOR THIS TERMINAL ARE ABORTED. IF
'ALL' IS SOECIFIED, ALL DEMAND TESTS IN
THE SYSTEM ARE ABORTED.

TO DETERMINE THE NUMBER OF A TERMINAL
WHICH ORIGINATED A DEMAND REQUEST, USE
THE 'DISPLAY PORT' AND 'DISPLAY DEMAND
QUEUE' COMMANDS.

NOTE: IF A DEMAND TEST IS IN PROGRESS,
IT WILL BE ABORTED AFTER THE CURRENT
TRUNK HAS COMPLETED TESTING.

    ->ABORT ROUTINE

STOPS ROUTINE TESTING WITHOUT AFFECTING
REGULAR START AND END TIMES. ROUTINE
TESTING WILL NOT START AGAIN UNTIL THE
REGULAR START TIME IS REACHED.

    ->RUN

RUNS THE PROGRAM-NAME

RUN'S THE RAMPART UTILITY PROGRAMS

'RUN USE' RUNS THE USER EDITOR(SAME AS
'EDIT' COMMAND)

'RUN CIP' RUNS THE CENTRAL OFFICE FILE
COMPILER(TYPE 'HELP DATABASE' FOR AN
EXPLANATION OF THE CONTENTS OF THIS
FILE)

'RUN TAC'